GREENchoice Fast Grab FRP Adhesive
Titebond GREENchoice Fast Grab FRP Adhesive is a high-quality, VOC-compliant, adhesive specifically formulated for the installation of FRP (fiber-reinforced plastic) panels. Its fast grab and bonding power greatly reduce the need for extended bracing.
GREENchoice Fast Grab FRP is environmentally superior and contains no ozone-depleting chemicals. Unlike solvent-based adhesives, it is nonflammable, emits no harmful fumes and cleans up with water.
Titebond GREENchoice FRP Adhesive Sales Sheet
For best results, store GREENchoice Fast Grab FRP Adhesive above 50°F. Do not use over treated plywood or metal, plastic, foam board, painted surfaces, sealed concrete, certain types of specially treated or moisture resistant gypsum wallboard, or other non-porous surfaces. For these substrates, for use on freezers, and any other application other than FRP, call Technical Service at 1-800-347-4583. KEEP FROM FREEZING
MEETS GREENSEAL GS-36, LEED, SCAQMD, CARB AND NAHB GREEN BUILDING SPECIFICATIONS. FDA AND CANADIAN FOOD INSPECTION AGENCY (CFIA) APPROVED FOR INDIRECT FOOD CONTACT.
Application Temperature
Over 50°F and below 90°F for adhesive and substrates.
Service Temperature Range
0°F. to 110°F.
Method of Application
The optimal trowel for best overall performance and coverage is a v-notch trowel, 3/16” wide x 1/4” deep, spaced 1/2” c.c. Trowels using dimensions other than the optimal size can be used, but they may affect working time and coverage. For additional trowel recommendations, please contact Franklin Technical Service at 1.800.347.4583.
Coverage
50 sq. ft. per gallon.
Working Time
20 minutes at 70°F.
Working Surfaces
Surfaces must be dry and free of any material that may deter adhesion, including severe and thick amounts of drywall joint compound. Patch large holes and depressions and remove any bumps or high spots, dust, oil, and grease. Concrete surfaces must be well cured and completely dry. Cut and pre-fit all panels. Lay fiberglass panels flat and let them acclimate to room temperature 24 hours before installing. Note: Panels used in conjunction with channel moldings should NOT fit tightly into the moldings. Leave a small gap under the molding for expansion and follow panel manufacturer’s recommendations. Any holes drilled through the panels for fasteners, pipes or conduits should be oversized to allow for natural movement of the panel. Click for FRP Installation Guide.
Cleanup
Tools and excess adhesive may be cleaned with water while wet. If adhesive has dried, use mineral spirits. Follow solvent vendor's precautions when using solvents. NOTE: Test solvent in an out-of-the-way area to make sure it will not mar or attack the surface.
PROvantage PRO Heavy Duty Construction Adhesive
PROvantage PRO Heavy Duty Adhesive is a premium-grade formula designed for more demanding construction and repair projects. It is ideal for bonding most common materials including wood, metal, brick, marble, ceramic tile, concrete, drywall and wet, frozen and treated lumber.
PRO Heavy Duty Adhesive meets today’s most stringent State and Federal VOC regulatory requirements. It fills gaps between materials, reduces the amount of nailing and can be extruded down to 0°F
Type: Proprietary synthetic polymerCalculated VOC: 44 g/LState : Thixotropic medium viscosity masticWeight/gallon : 10.6 lbs.Color : BrownFlashpoint : < 0°FSolids : 66%Freeze/thaw stability : Will not freezeViscosity : 160,000 cpsStorage life : 18 months in tightly closed containers at 75°F
COVERAGE (MAXIMUM): APPROXIMATE LENGTH OF BEAD ACCORDING TO BEAD DIAMETER
Container
1/8” bead 1/4” bead 3/8” bead
10 oz. Cartridge 123 ft. 30 ft. 13 ft.
28 oz. Cartridge 343 ft. 86 ft. 38 ft.
Application Temperature
0ºF to 100ºF
Service Temperature Range
-20ºF to 120ºF
Method of Application
Cartridge/caulking gun
Working Time
Approximately 20 minutes for a 1/4" bead
Working Surfaces
Surfaces to be bonded should be clean, dry and free from excessive oil, grease, water, dirt or any other material that may deter adhesion.
Cleanup
Tools/adhesive may be cleaned with acetone or mineral spirits. Follow solvent vendor’s precautions. NOTE: Test solvent on an out-of-the way area to make sure it will not mar or attack the surface.
EXCEEDS THE REQUIREMENTS OF APA’S AFG-01, ASTM C557 AND ASTM D3498.
PROvantage Weatherproof Subfloor Adhesive
PROvantage™ Weatherproof Subfloor Adhesive is a high-performance, VOC-compliant formula ideal for subfloor installations and general plywood use. It offers a strong initial tack and excellent bond strength for particleboard,
OSB, engineered lumber and wet, frozen and treated lumber.
PROvantage Subfloor Adhesive provides a permanent bond that remains flexible, reduces nailing and eliminates squeaky floors. It can be easily extruded from 0°F - 100°F for applications in various climates.